[rescue] SGI stuff that needs a home!

Jonathan Katz jon at jonworld.com
Thu May 8 08:53:18 CDT 2014

These are posted on Nekochan but I have no takers :(

1) Indigo2... I think it's a 200Mhz R4400, ZX graphics, 64M of RAM.
Green, with feet.

2) SGI O2 PARTS (system case was not worth saving; too many broken
skins and bent chassis)

6x Kingston-branded O2 RAM. 32M sticks, branded KGS-O2/32. Small yellow mark.
2x SGI-branded O2 RAM. 32M sticks. P/N 030-0881-002 100Mhz Hitachi
chips. marked purple
4x SGI-branded O2 RAM. 32M sticks. P/N 030-0876-002 100Mhz NEC chips.
one pair red, one pair yellow
1x O2 power supply. SGI P/N 060-0032-001 Sony branded.
1x AV module. It was working but the O2 Camera connector housing is bent.
1x SGI O2 drive tray. It has an IBM 36.4G SCA drive in it that is
working. I can send with or without the drive.
1x PCI riser assembly, SGI P/N 013-2196-001

3) SGI Fuel, 600 Mhz. hinv:

1 600 MHZ IP35 Processor
CPU: MIPS R14000 Processor Chip Revision: 2.3
FPU: MIPS R14010 Floating Point Chip Revision: 2.3
CPU 0 at Module 001c01/Slot 0/Slice A: 600 Mhz MIPS R14000 Processor
Chip (enabled)
  Processor revision: 2.3. Scache: Size 4 MB Speed 300 Mhz  Tap 0xa
Main memory size: 1024 Mbytes
Instruction cache size: 32 Kbytes
Data cache size: 32 Kbytes
Secondary unified instruction/data cache size: 4 Mbytes
Memory at Module 001c01/Slot 0: 1024 MB (enabled)
  Bank 0 contains 512 MB (Standard) DIMMS (enabled)
  Bank 1 contains 512 MB (Standard) DIMMS (enabled)
Integral SCSI controller 0: Version QL12160, low voltage differential
  Disk drive: unit 1 on SCSI controller 0 (unit 1)
Integral SCSI controller 1: Version QL12160, low voltage differential
IOC3/IOC4 serial port: tty1
IOC3/IOC4 serial port: tty2
IOC3 parallel port: plp1
Graphics board: V10
Integral Fast Ethernet: ef0, version 1, module 001c01, pci 4
  PCI Adapter ID (vendor 0x1077, device 0x1216) PCI slot 1
  PCI Adapter ID (vendor 0x10a9, device 0x0003) PCI slot 4
  PCI Adapter ID (vendor 0x11c1, device 0x5802) PCI slot 5
HUB in Module 001c01/Slot 0: Revision 2 Speed 200.00 Mhz (enabled)
IP35prom in Module 001c01/Slot n0: Revision 6.210
USB controller: type OHCI

4) Challenge/Onyx parts:

3x IO4 "primary" break outs (serial, ethernet, parallel) SGI P/N 030-0341-005 #B

5x "null" airflow/spacer VME space boards, I believe P/N 313-0889-002
--- much of the foam has fallen off

IO4 Primary and Secondary hooked together 030-0341-005 and
030-0329-??? ... so the same as before, but with a 2nd row for
monitor, keyboard, mouse, etc.

A different break-out IO panel for a frame grabber, P/N 030-0292-003

Break-out/bulkhead (with cable) for external SCSI.

Realty Graphics FunStuffs(tm)
030-0233-001A -- the board used to link multiple RE boards together.
030-0413-004 DG2
030-0363-005 GE10
030-0359(?)-001 RM4
030-0284-004 VS2
030-0342-007 VO2 (Sirius board) ... I do not have a Sirius break-out
box! I DO have all the connectors for the bulkhead, though.

Full set of terminating resistors for reality graphics

Some kind of power distribution board, 030-0264-004

3x MC3
030-0604-106 MC3 .. all banks with 2 SIMMs except one.
A second MC3 with all banks half-loaded.
A 3rd MC3 with only one bank loaded (or one SIMM in each bank.)

A different power distribution board (which I need to take a 2nd
picture of to read the P/N)

I have 2x 505x2 power boards, 030-0318-003

Both SCSI JBOD trays

2x IO4. One is working 100%, the other I'm not 100% sure on.

Mezzanine cards for the IO4s.
030-0242-005 (additional SCSI controller?)
One with two FDDI cards (I have the FDDI accessories/break-out panels, etc.)
One 030-0501-003 "short mezf"

Remote VCAM 030-0502-205 for sending data to your remote VME box.

A 3 VME -> 2 VME adapter with some kind of digital audio
configuration. Best guess as to a P/N is 013-7032-001

IP19 CPU Boards.
I have a few 4 CPU boards and a few 2 CPU boards. The totals come out
to be 12x 200Mhz R4400s and 2x 250Mhz R4400s.

Jonathan Katz, Indianapolis, IN.

More information about the rescue mailing list